Simple Customization (Minimum Q’ty: 100pcs)

1. Connector
   • Applying customized connectors on the opposite side of actuator
2. Wire
   • Customize wire length, thickness, color, wire shield, etc.
3. Parameter
   • Parameter changes using Servo Manager Software from factory. (Ex -Overload Protection Off, Stroke change from 27mm to 30mm, Stroke limit change, etc)
     

※ According to special wire and connector’s MOQ, prepayment for the actual cost of those wires and connectors may be required.

Special Customization (Minimum Q’ty: 100pcs)

1. Greese
   • Change to special grease or spread volume change : for durability, we need to test it based on request.
     ※ For special grease, we may require some prepayment to secure it.
2. Rod End Tip / Rod
   • Special shape rod end tip.
   • Rod material change.
   • Drawing is required.
3. Rod-End Starting Point Adjustment
   • The general specification for the starting point (when fully retracted) tolerance is +/-0.5mm.
   • For the same model, there may be a slight difference in starting point depending on the assembly characteristics.
   • For customers who want to precisely match the starting position of the rod-end for the customer’s special application, we can match the tolerance to +/- 0.1mm or less. (with some charge)
4. Firmware
   • Add special feature or Control characteristic change including PID value change
     Ex) We are applying slightly different PID value for certain application according to customer request
5. Metal Parts (Center/Output gears, Rod-insert) 
   • The standard engineering plastic center gear, output gear and rod insert have been developed through intensive test considering for durability, impact resistance and lubricity.
   • Under special condition, however, we can apply metal parts for those plastic parts for better impact resistance.
   • If we apply metal parts, lifecycle of actuator will be shortened due to gear wearing (1/5 of engineering plastic gear) and mechanical play can be made faster.
   • Therefore, metal parts can be applied for the application whose operation frequency is not that high while they need stronger impact resistance.
   • Metal center gear can be applied to all stroke lineup except for 27mm stroke version.
6. Top case
   
   
   • The Top case(Yellow marked) can be changed as above according to customer’s request.
   • Custom1-Plastic Flat : Same engineering plastic material with 4 x mounting holes.
   • Custom2-Metal Flat : Metal alloy, Mounting hole can be customized to M3 or M4 (standard : M2.5) (Material cost to be increased).
   • Change at customer’s side is not permitted. (Change at factory only)
7. Connector Outlet (Minimum Q’ty : 200pcs)
   • Original
     
     
   • Custom 1 – Rubber Cap
     – Applying rubber cap without connector for water/dust tight condition.
     
     
   • Custom 2 – Remove Connector Outlet
     – Remove connector outlet for space constraint
     – Need to make a new PC board and prepayment(U$5,000) for the 500pcs PCB will be required.
     – Actuator can be shipped partially(more than 50pcs)
     – Prepaid amount will be deducted from the actuator cost)
     
     
8. Circuitry (Minimum Q’ty: 500pcs)
   • PCB change
     – As mentioned before, prepayment(U$5,000) for the 500pcs PCB will be required. Actuator can be shipped partially(more than 50pcs) and prepaid amount will be deducted from the actuator cost.
   • Special motor
     – (Voltage/ Force/lifespan) : Due to MOQ of DC motor, prepayment is required for DC motor cost. Prepaid amount will be deducted from the actuator cost.

Complicated Level Customization

Minimum Q’ty: Please consult.


• New mold or Mold change (Redesign shape body case)
• Considerable development cost will be required due to long-term R&D period and resource.
• There is a possibility that the proposal will not be adopted due to our workforce status or development plan priorities.